Router Table - Find out how to Use

Want to router know how one can use a Router Table? Here are tips to get the most out of your router table.

You don't want a miter channel. Usually, you slide your work alongside the fence. If using a miter channel, then the fence have to be square to the miter channel. Why go to that hassle?

You'll be able to create a jig to glide alongside the Fence. This automatically aligns the wood to get a square cut. You may make adjustment in profile and depth of cut. A Router Elevate makes this easy.

A quality Router Table fence eases mud collection. Use your Router Table and Fence for simplicity and ease!

You need to never put your work between the fence and the router bit. That is simply asking for trouble.

Usually, you slide the wood from proper to left (when looking at the fence from the entrance). That is an anti-climb cut. You make nearly all cuts this way.

If very cautious, you can go a brief distance in the opposite direction. But it's essential to maintain on tight to keep away from kickback and/or injury. This climb minimize offers cleaner edges, but you should solely attempt it after loads of experience.

Only do netgear lower than 15% of your work this way. You need to solely use shallow or gentle cuts. Do NOT take massive cuts. Only do it if you palms are protected and away from the router bit.

How one can use a Router Table to middle edge-to-edge joints:

Have you ever ever wondered how one can middle edge-to-edge joints? You use this method for making stable tabletops, vast panels, or even make edging to go around your router desk top.

Let's use an precise instance of oak edging on a MDF Router Table Top. The highest is 1 1/8" thick. The oak edging is 1 1/8" thick.

How will we ensure a centered edge?

Determine on the tongue dimension. You've gotten a 1/four" slot cutter. You want the tongue thickness lower than two occasions the cut. Therefore, the tongue thickness is barely lower than half of". We use a 1/four" depth of minimize for this example.
We wish a tongue that is lower than half of" in thickness. Therefore, we know that the rabbet on the Table belkin High is barely more than 5/sixteen" on both sides of a 1 1/8" thick piece.
Rabbet the highest with a rabbet bit with a bearing to supply a 1/four" rabbet. You don't wish to take a lot during your first pass. Therefore, the depth of minimize is ready for 1/8" in your first pass.
Set the fence so it's even with the bearing of the rabbet bit.
Minimize each prime and backside of the top. Take your time and go all the way in which around. Be sure the workpiece is flat on the Router Table Top. Or use the router on prime of the workpiece.
Measure the thickness of the tongue. Whether it is bigger than half of", then regulate the depth of cut. A router carry makes this easy. Word: you rout both sides; subsequently use one-half the adjustment for every side.
Make your adjustment, rout the highest and backside again. The tongue's thickness is now barely lower than half of".
Replace your rabbeting bit with your 1/four" slot cutter. I at all times disconnect the facility source to the router earlier than changing bits!
Sit the rabbeted piece on the router tabletop close to the slot cutter. Increase the Router so the underside of the slot cutter aligns with the underside of the tongue. You could want assist if the workpiece is large.
Set the depth of minimize for the slot to around 3/sixteen" initially. Now slot your Oak edging. Flip it over and slot again. Take a look at the slot on the tongue. Is it too tight? If that's the case, keep in mind that you make two passes with the slotter. Only decrease your slot bit by half of of the dimension needed. By the way in which, the Porter Cable 7518 Router makes this a snap.
For the reason that slot minimize is 1/four", the second pass just isn't using your entire cutter. You get an precisely middle slot that matches on the tongue.
Once the slot (groove) suits on the tongue, you are ready to set your final depth of the groove. The ultimate depth of minimize is barely more than 1/four" to allow for glue.
Set your fence for this final depth. Keep in mind - make two passes with the slotter. This gives you an exact fit.

You should use this method for any edge-to-edge joinery, akin to tabletops, panels, massive drawer fronts, and any time you wish to be a part of two-pieces. You get excellent alignment and a rock-stable joint.

If you want to see how this looks after glue-up, please go to Router Table High

To make your personal router carry, go to a simple to make Router Elevate

For more information on Using Your Router Table, including footage and ideas, please go to How one can Use a Router Table

Posted in: Router